4.5A Laser Diode and TEC Driver, 445nm, 635nm, 650nm, DPSS Laser

Description

Lasertack
High Quality
Fast shipping
Customer service
4.5A Laser Diode Driver with TEC Controller
Our newly developed iLD driver series is a huge improvement of the popular SHS and LDTEC drivers.
Equipped with several safety features, this driver offers high reliability and safety.
Features:
LED indicators
The LED indicators show in real-time the current state of all functions and driver state. Operating at normal conditions or failure state are immediately shown.
Temperature monitoring
With a temperature sensor connected, the temperature monitoring is active. The measured values are used for overtemperature shutdown and TEC controller (sold separately).
Safety shutdown
The driver shuts down the laser when overtemperature is detected or the interlock loop is broken. The LED indicators show what kind of failure ocurred.
Active and passive interlock
Active an passive interlock loops are accepted. A simple door switch or a 5 V interlock loop can be connected.
Turn-on delay
After connecting the power supply, the driver allows the PSU to stabilize before enabling the laser output.
Programmable failure treatment
In case of a failure because of overtemperature or broken interlock, the driver can handle the situation in two ways. It can restart the laser when the failure caused problem is solved automatically or it will wait for a restart signal. The programming is done by shorting of of the two connector pins pairs.
​​​​​​​
↵
Model
iLD-2500
Current LD/TEC (mA)
2500 / 2000
Supply voltage (VDC)
5-24
Modulation (kHz)
CW~250
Dimesnions (L x B x H mm³)
83 x 37 x 23,7
TEC current (mA)
2000
Buy it now
Payment
Shipping
Service
Payment
Shipping
Service
We accept payment via PayPal or wire. No check or credit card are accepted.
The spectrometer will be shipped with ensured and trackable service.
Contact us at any time when you need assistance. We are glad to help before and after your purchase.
High Quality
Fast shipping
Customer service
See our other items
Our newly developed iLD driver series is a huge improvement of the popular SHS and LDTEC drivers. Equipped with several safety features, this driver offers high reliability and safety. Features: LED indicators The LED indicators show in real-time the current state of all functions and driver state. Operating at normal conditions or failure state are immediately shown. Temperature monitoring With a temperature sensor connected, the temperature monitoring is active. The measured values are used for overtemperature shutdown and TEC controller (sold separately). Safety shutdown The driver shuts down the laser when overtemperature is detected or the interlock loop is broken. The LED indicators show what kind of failure ocurred. Active and passive interlock Active an passive interlock loops are accepted. A simple door switch or a 5 V interlock loop can be connected. Turn-on delay After connecting the power supply, the driver allows the PSU to stabilize before enabling the laser output. Programmable failure treatment In case of a failure because of overtemperature or broken interlock, the driver can handle the situation in two ways. It can restart the laser when the failure caused problem is solved automatically or it will wait for a restart signal. The programming is done by shorting of of the two connector pins pairs. ​​​​​​​
Lasertack
4.5A Laser Diode Driver with TEC Controller
Our newly developed iLD driver series is a huge improvement of the popular SHS and LDTEC drivers.
Equipped with several safety features, this driver offers high reliability and safety.
Features:
LED indicators
The LED indicators show in real-time the current state of all functions and driver state. Operating at normal conditions or failure state are immediately shown.
Temperature monitoring
With a temperature sensor connected, the temperature monitoring is active. The measured values are used for overtemperature shutdown and TEC controller (sold separately).
Safety shutdown
The driver shuts down the laser when overtemperature is detected or the interlock loop is broken. The LED indicators show what kind of failure ocurred.
Active and passive interlock
Active an passive interlock loops are accepted. A simple door switch or a 5 V interlock loop can be connected.
Turn-on delay
After connecting the power supply, the driver allows the PSU to stabilize before enabling the laser output.
Programmable failure treatment
In case of a failure because of overtemperature or broken interlock, the driver can handle the situation in two ways. It can restart the laser when the failure caused problem is solved automatically or it will wait for a restart signal. The programming is done by shorting of of the two connector pins pairs.
​​​​​​​
Buy it now
Payment
We accept payment via PayPal or wire. No check or credit card are accepted.
Shipping
The spectrometer will be shipped with ensured and trackable service.
Service
Contact us at any time when you need assistance. We are glad to help before and after your purchase.
See our other items
High Quality
Fast shipping
Customer service
Our newly developed iLD driver series is a huge improvement of the popular SHS and LDTEC drivers.
Equipped with several safety features, this driver offers high reliability and safety.
Features:
LED indicators
The LED indicators show in real-time the current state of all functions and driver state. Operating at normal conditions or failure state are immediately shown.
Temperature monitoring
With a temperature sensor connected, the temperature monitoring is active. The measured values are used for overtemperature shutdown and TEC controller (sold separately).
Safety shutdown
The driver shuts down the laser when overtemperature is detected or the interlock loop is broken. The LED indicators show what kind of failure ocurred.
Active and passive interlock
Active an passive interlock loops are accepted. A simple door switch or a 5 V interlock loop can be connected.
Turn-on delay
After connecting the power supply, the driver allows the PSU to stabilize before enabling the laser output.
Programmable failure treatment
In case of a failure because of overtemperature or broken interlock, the driver can handle the situation in two ways. It can restart the laser when the failure caused problem is solved automatically or it will wait for a restart signal. The programming is done by shorting of of the two connector pins pairs.
​​​​​​​